DF-5560 / panic.txt
h error=6 [df5558] attachiic try 1: device_probe_and_attach error=6 [df5558] attachiic try 2: device_probe_and_attach error=6 [df5558] attachiic try 3: device_probe_and_attach error=6 [df5558] attachiic try 4: device_probe_and_attach error=6 [df5558] attachiic try 5: device_probe_and_attach error=6 [df5558] iicbus0 child 0: name=ic unit=0 [df5558] iicbus0 child 1: name=iic unit=0 [df5558] iicbus0 child 2: name=iicsmb unit=0 [df5558] attachiic try 0: device_probe_and_attach error=6 [df5558] attachiic try 1: device_probe_and_attach error=6 [df5558] attachiic try 2: device_probe_and_attach error=6 [df5558] attachiic try 3: device_probe_and_attach error=6 [df5558] attachiic try 4: device_probe_and_attach error=6 [df5558] attachiic try 5: device_probe_and_attach error=6 [df5558] groom5558 unloaded (grooms=0) iicbus0: detached iicbb0: detached fakebb0: detached fakebb0: <fake GPIO bit-bang i2c master+slave> on motherboard iicbb0: <I2C bit-banging driver> on fakebb0 iicbus0: <Philips I2C bus> on iicbb0 addr 0xff [fakebb] attach done: resets=3 resets_with_oldaddr=1 bus=0xfffff8011775d6e0 [fakebb] request_bus error=0 [fakebb] write: error=0 sent=8 slave_rx=deadbeef55aa1234 ok=1 [fakebb] read: error=0 read=8 data=c0c1c2c3c4c5c6c7 ok=1 [fakebb] nacked-write: error=2 (IIC_ENOACK=2) bus_started_after=0 [fakebb] repstart-read: error=0 byte=0xc0 (expect 0xc0) [fakebb] SUMMARY: write_ok=1 read_ok=1 starts=5 stops=4 rxlen=0 spray_sink=0 rdrand0: No RdRand support. [df5558] groom5558 loaded (sink=0) [df5558] iicbus0 child 0: name=ic unit=0 [df5558] iicbus0 child 1: name=iic unit=0 [df5558] iicbus0 child 2: name=iicsmb unit=0 [df5558] readivar: BUS_READ_IVAR error=6 (ENXIO=6) v=0x77777777 (UNTOUCHED -- nobody writes *result) [df5558] iicbus0 child 0: name=ic unit=0 [df5558] iicbus0 child 1: name=iic unit=0 [df5558] iicbus0 child 2: name=iicsmb unit=0 [df5558] attachiic try 0: device_probe_and_attach error=6 [df5558] attachiic try 1: device_probe_and_attach error=6 [df5558] attachiic try 2: device_probe_and_attach error=6 [df5558] attachiic try 3: device_probe_and_attach error=6 [df5558] attachiic try 4: device_probe_and_attach error=6 [df5558] attachiic try 5: device_probe_and_attach error=6 [df5558] groom5558 unloaded (grooms=0) iicbus0: detached iicbb0: detached fakebb0: detached fakebb0: <fake GPIO bit-bang i2c master+slave> on motherboard iicbb0: <I2C bit-banging driver> on fakebb0 iicbus0: <Philips I2C bus> on iicbb0 addr 0xff [fakebb] attach done: resets=3 resets_with_oldaddr=1 bus=0xfffff8008bb646e0 [fakebb] request_bus error=0 [fakebb] write: error=0 sent=8 slave_rx=deadbeef55aa1234 ok=1 [fakebb] read: error=0 read=8 data=c0c1c2c3c4c5c6c7 ok=1 [fakebb] nacked-write: error=2 (IIC_ENOACK=2) bus_started_after=0 [fakebb] repstart-read: error=0 byte=0xc0 (expect 0xc0) [fakebb] SUMMARY: write_ok=1 read_ok=1 starts=5 stops=4 rxlen=0 spray_sink=0 rdrand0: No RdRand support. iic0: <I2C generic I/O> on iicbus0 [df5558] groom5558 loaded (sink=0) [df5558] iicbus0 child 0: name=ic unit=0 [df5558] iicbus0 child 1: name=iic unit=0 [df5558] iicbus0 child 2: name=iicsmb unit=0 [df5558] readivar: BUS_READ_IVAR error=0 (ENXIO=6) v=0x0 (written) Fatal user address access from kernel mode from rdwrleak at ffffffff8068d140 Fatal trap 12: page fault while in kernel mode cpuid = 3; lapic id = 3 fault virtual address = 0x28 fault code = supervisor read data, page not present instruction pointer = 0x8:0xffffffff8068d140 stack pointer = 0x10:0xfffff801184076d0 frame pointer = 0x10:0xfffff80118407738 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, long 0, def32 0, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 2071 current thread = pri 6 kernel: type 12 trap, code=0 CPU3 stopping CPUs: 0x00000037 stopped Stopped at device_get_parent: movq 0x28(%rdi),%rax db>